Alarmy maszyny
- 1001 Błąd 1001: Brak sygnału sprzężenia zwrotnego osi X ›
- achieve_processing_times Alarm: Achieve processing times ›
- axis_4limit_+__axis_4limit_- Alarm: Axis 4Limit + / Alarm: Axis 4Limit - ›
- bcl4516_unconnected_id:210844120267 Alarm: BCL4516 unconnected ID:210844120267 ›
- bcs100_alarm_found_network_failed BCS100 Alarm Found, NETWORK FAILED ›
- calibration_abnormal_end__not_detect_cap_change Calibration Abnormal End Alarm: Not Detect Cap Change ›
- capacitance_diminished_1_-_10_000 Alarm: Capacitance diminished 1 - 10 000 ›
- capacitiance_become_0 Alarm: Capacitiance become 0 ›
- clear_warning_z-_follow_device_hardware_negative_l Clear Warning Z- Follow device hardware negative limit alarm ›
- cuttinghead_alarm_please_check_cuttinghead cuttinghead alarm, please check cuttinghead ›
- e001:_w_-_axis_negative_limit_alarm E001: W - axis negative limit alarm ›
- e009:_2y_detection_alarm E009: 2Y Detection alarm ›
- e015:_wireless_signal_of_handle_interrupts E015: Wireless signal of handle interrupts ›
- emergency_stop_bcs100_emergency_stop Emergency Stop BCS100 emergency stop ›
- ethercat:_slave_run_abnormal._check_connection Alarm: Ethercat: Slave Run Abnormal. Check Connection ›
- exceed_positive_stroke_of_z_axis_exceed_negative_ Alarm: exceed positive stroke of Z axis, exceed negative stroke of axis Z ›
- follow_exceed_lower_soft_limit Alarm: Follow exceed lower soft limit ›
- follow_exceed_upper_soft_limit Alarm: Follow exceed upper soft limit ›
- following_deviation_is_too_large Odchylenie śledzenia jest zbyt duże ›
- gas__oxygen Alarm: Gas Alarm: Oxygen ›
- motor_/_encoder_abnormally_moving Alarm: Motor / Encoder abnormally moving ›
- no_air_gas Alarm: No AIR GAS ›
- oil Alarm: oil ›
- only_continue_to_use_by_returning_to_origin_x_axi Alarm: Only continue to use by returning to origin, X Axis soft limit -, X Axis soft limit +, Y AxisSoft Limit-, Y AxisSoft Limit+ ›
- pallet_arrive_signal_not_detected Pallet arrive signal not detected ›
- pending_motion_out_of_range Pending motion out of range ›
- self-lubricating__pump_over_pressure Self-lubricating Alarm: Pump over pressure ›
- system_stiffness_too_low! Alarm: System stiffness too low! ›
- tip_touch Alarm: Tip Touch ›
- water_alarm Alarm: Water ALARM ›
- x_axis_servo_alarm_y_axis_servo_alarm_z_axis_ser Alarm: X Axis Servo alarm, Y Axis Servo alarm, Z Axis Servo alarm ›
- x_axis_servo_alarm_yaxis_servo_alarm_axis_3servo Alarm: X Axis Servo alarm, YAxis Servo alarm, Axis 3Servo alarm, Emergency Stop, Servo alarm, BCS100 ›
- y_axis_limit___y_axis_limit_-__x_axis_limit_+._y Alarm: Y Axis Limit , Y Axis Limit -, X Axis Limit +. Y Axis Limit - ›
- ycmd_out_range: Ycmd out range: ›
- аварийная_сигнализация_only_continue_to_use_by_ret Alarm: Only continue to use by returning to origin ›
- 2001 Błąd 2001: Niskie ciśnienie gazu pomocniczego ›
- 3001 Błąd 3001: Błąd czujnika wysokości ›