Fiber laser settings for 1 mm mild steel at 1 kW

Updated:

Short answer

A 1 kW fiber laser cuts 1 mm mild steel with nitrogen or air at 11–16 bar and 6–22 m/min. For this combination we have four regimes: the base one from the source maker’s table and three alternatives from other sources.

Mild steel cutting speed and gas pressure at 1 kW

Base regime · Mild steel · 1 mm · 1 kW
1000W(50u), Cutting head focal length: Collimating 100/Focal 125
Gas
N₂ / air
Gas pressure
14bar
Speed
20–22m/min
Power
100%
Frequency
5000Hz
Duty cycle
100%
Focus
in the app
Cutting height
in the app
Nozzle
in the app
Alternative 1 · Mild steel · 1 mm · 1 kW
Raycus 1000W, Head: none
Gas
N₂ / air
Gas pressure
16bar
Speed
10m/min
Power
100%
Frequency
5000Hz
Duty cycle
100%
Focus
in the app
Cutting height
in the app
Nozzle
in the app
Alternative 2 · Mild steel · 1 mm · 1 kW
1000W, Head: ProCutter
Gas
N₂ / air
Gas pressure
16bar
Speed
6m/min
Power
100%
Frequency
1000Hz
Duty cycle
100%
Focus
in the app
Cutting height
in the app
Nozzle
in the app
Alternative 3 · Mild steel · 1 mm · 1 kW
Max MFSC-1000X QBH, Head: none
Gas
N₂ / air
Gas pressure
11bar
Speed
12.5m/min
Power
100%
Frequency
5000Hz
Duty cycle
100%
Focus
in the app
Cutting height
in the app
Nozzle
in the app

Which regime to start with

Cutting time and gas consumption per metre

At these speeds one metre of cut takes about 3–10 seconds. Nitrogen or air flow through the nozzle is about 9.6–76.6 m³ per hour, or 27–64 litres per metre of cut, not counting piercing.

Mild steel cutting speed chart: neighbouring thickness and power

Thickness · powerGasSpeed, m/min
0.8 mm · 1 kW N₂ / air19
1 mm · 500 W N₂ / air10–12
1 mm · 1 kW N₂ / air20–22
1 mm · 1.5 kW N₂ / air20
1 mm · 2 kW N₂ / air25
2 mm · 1 kW N₂ / air6–7
3 mm · 1 kW O₂2.8–3

Common mild steel cutting defects with nitrogen or air

Cut loss / Beam reflection
Cut loss / Beam reflection The beam breaks down, upward sparking occurs, and the metal is not cut through along the contour. Cause: Insufficient energy density, excessive cutting speed, incorrect focus. First step: Decrease the speed (step 5%). Fiber laser stopped cutting through the sheet — what is wrong?
Burn-throughs in the lower section (Breakthrough)
Burn-throughs in the lower section (Breakthrough) Burnout of metal at the bottom of the edge with formation of craters and buildup. Cause: Excessive cutting speed combined with insufficient assist gas pressure. First step: Decrease the cutting speed (step 5%). Where should the focus sit for stainless steel and mild steel?
Sharp hard dross
Sharp hard dross A sharp welded dross forms along the entire bottom edge. Cause: Focus set too deep, assist gas flow rate too low. First step: Lower/raise the focus (step 0.5 mm). How do I get rid of dross when cutting mild steel with oxygen?

Not sure which one you have? Send a photo of the edge to the app and it names the defect and the fix.

Related questions

Can a 1 kW fiber laser cut 1 mm mild steel with oxygen?
Our tables give only nitrogen or air for 1 mm mild steel: on thin sheet it is faster and leaves a clean edge.
What is the thickest mild steel a 1 kW fiber laser cuts?
Our tables go up to 14 mm mild steel at 1 kW, at 0.07 m/min with nitrogen or air. The next thickness, 15 mm, starts from 3 kW.
Why is the speed a range?
Sheet surface, mild steel grade, gas purity and pressure at the nozzle and the state of the protective window all shift the result. Start at the lower value, make a test cut and raise the speed in 5% steps while the bottom edge stays clean.
Where are focus, cutting height and nozzle?
They depend on the cutting head and lens, so a single number is often wrong for your machine. The app shows the full regime and fits it to the machine you add to your profile.

Ranges are given for a typical 3–6 kW fiber machine with a clean beam path. Always verify against your machine manufacturer’s table before production.

Need the numbers for your exact machine?

See what is inside

SBM Laser Help carries cutting and piercing parameter tables by material, thickness and gas, photo diagnosis of cut defects, machine and chiller error codes, and gas consumption calculators. Free account, no card.