Fiber laser settings for 12 mm mild steel at 6 kW

Updated:

Short answer

A 6 kW fiber laser cuts 12 mm mild steel with oxygen at 0.6–0.85 bar and 0.9–2.1 m/min. For this combination we have 9 regimes: two base ones from the source makers’ tables and seven alternatives from other sources.

Mild steel cutting speed and gas pressure at 6 kW

Base regime · O₂ 1 · Mild steel · 12 mm · 6 kW
RFL-6000(100u), Cutting head focal length: Collimating 100/Focal 200
Gas
O₂
Gas pressure
0.6bar
Speed
0.9–1m/min
Power
37%
Frequency
5000Hz
Duty cycle
37%
Focus
in the app
Cutting height
in the app
Nozzle
in the app
Base regime · O₂ 2 · Mild steel · 12 mm · 6 kW
RFL-6000(100u), Cutting head focal length: Collimating 100/Focal 200
Gas
O₂
Gas pressure
0.6bar
Speed
1.9–2.1m/min
Power
100%
Frequency
5000Hz
Duty cycle
100%
Focus
in the app
Cutting height
in the app
Nozzle
in the app
Alternative 1 · Mild steel · 12 mm · 6 kW
MAX MFSC-6000W-100um, Head: none
Gas
O₂
Gas pressure
0.6bar
Speed
1.9m/min
Power
100%
Frequency
5000Hz
Duty cycle
100%
Focus
in the app
Cutting height
in the app
Nozzle
in the app
Alternative 2 · Mild steel · 12 mm · 6 kW
Raycus, Head: raytools BM06K
Gas
O₂
Gas pressure
0.7bar
Speed
1.95m/min
Power
90%
Frequency
5000Hz
Duty cycle
100%
Focus
in the app
Cutting height
in the app
Nozzle
in the app
Alternative 3 · Mild steel · 12 mm · 6 kW
Raycus, Head: raytools BM06K
Gas
O₂
Gas pressure
0.72bar
Speed
1.85m/min
Power
90%
Frequency
5000Hz
Duty cycle
100%
Focus
in the app
Cutting height
in the app
Nozzle
in the app
Alternative 4 · Mild steel · 12 mm · 6 kW
MAX, Head: none
Gas
O₂
Gas pressure
0.85bar
Speed
1.4m/min
Power
100%
Frequency
5000Hz
Duty cycle
100%
Focus
in the app
Cutting height
in the app
Nozzle
in the app
Alternative 5 · Mild steel · 12 mm · 6 kW
IPG, Head: none
Gas
O₂
Gas pressure
0.68bar
Speed
1.8m/min
Power
90%
Frequency
5000Hz
Duty cycle
100%
Focus
in the app
Cutting height
in the app
Nozzle
in the app
Alternative 6 · Mild steel · 12 mm · 6 kW
Raycus, Head: BOCI BLT421
Gas
O₂
Gas pressure
0.65bar
Speed
1.6m/min
Power
90%
Frequency
4000Hz
Duty cycle
80%
Focus
in the app
Cutting height
in the app
Nozzle
in the app
Alternative 7 · Mild steel · 12 mm · 6 kW
IPG, Head: none
Gas
O₂
Gas pressure
0.64bar
Speed
1.98m/min
Power
95%
Frequency
5000Hz
Duty cycle
100%
Focus
in the app
Cutting height
in the app
Nozzle
in the app

Which regime to start with

Cutting time and gas consumption per metre

At these speeds one metre of cut takes about 29–67 seconds. Oxygen flow through the nozzle is about 1.2–7.7 m³ per hour, or 10–143 litres per metre of cut, not counting piercing.

Mild steel cutting speed chart: neighbouring thickness and power

Thickness · powerGasSpeed, m/min
8 mm · 6 kW O₂2.2–2.5
10 mm · 6 kW O₂2–2.3
12 mm · 4 kW O₂1–1.2
12 mm · 6 kW O₂0.9–1
12 mm · 6 kW O₂1.9–2.1
12 mm · 8 kW O₂1.8–2
12 mm · 10 kW O₂1.8–2
14 mm · 6 kW O₂0.8–0.9
14 mm · 6 kW O₂1.4–1.7
16 mm · 6 kW O₂0.8–0.9
16 mm · 6 kW O₂1.2–1.4

Going from 6 kW to 8 kW gives about 100% more speed on 12 mm with oxygen. Nitrogen or air cuts about 5.8 times as fast as oxygen here, but needs 15 kW.

Common mild steel cutting defects with oxygen

Roughness with fine burrs
Roughness with fine burrs Rough cut surface across the full material thickness with formation of fine powdery dross on the bottom. Cause: Focus position set too high, oxygen pressure too low. First step: Raise/lower the focus (step 0.5 mm). Why is the cut edge rough and striated instead of smooth?
Hard metallic dross
Hard metallic dross A dense, hard-to-remove welded dross forms on the bottom edge of the part, requiring grinding with an angle grinder. Cause: Low oxygen pressure, excessive cutting speed, focus position set too high, insufficient power. First step: Increase the oxygen pressure (step 0.1 bar). How do I get rid of dross when cutting mild steel with oxygen?
Brittle (easy-to-remove) dross
Brittle (easy-to-remove) dross A thin, brittle burr hangs from the bottom edge that is easily knocked off with a scraper or hammer. Cause: Excessive cutting speed, slightly buried focus, minor assist gas pressure deviation. First step: Raise the focus (step 0.5 mm). How do I get rid of dross when cutting mild steel with oxygen?
Long thick dross
Long thick dross Large, massive drops and 'icicles' of solidified metal hang from the bottom edge. Cause: Low assist gas pressure, excessive speed, focus position set too high. First step: Increase the oxygen pressure (step 0.1 bar). How do I get rid of dross when cutting mild steel with oxygen?

Not sure which one you have? Send a photo of the edge to the app and it names the defect and the fix.

Related questions

Can a 6 kW fiber laser cut 12 mm mild steel with nitrogen or air?
Our tables give nitrogen or air for 12 mm mild steel starting from 15 kW, at 5–6 m/min. At 6 kW the working choice is oxygen: the burning iron adds the heat the beam alone does not have.
What is the thickest mild steel a 6 kW fiber laser cuts?
Our tables go up to 25 mm mild steel at 6 kW, at 0.5 m/min with oxygen. The next thickness, 26 mm, starts from 3 kW.
Why is the speed a range?
Sheet surface, mild steel grade, oxygen purity and the state of the protective window all shift the result. Start at the lower value, make a test cut and raise the speed in 5% steps while the bottom edge stays clean.
Where are focus, cutting height and nozzle?
They depend on the cutting head and lens, so a single number is often wrong for your machine. The app shows the full regime and fits it to the machine you add to your profile.

Ranges are given for a typical 3–6 kW fiber machine with a clean beam path. Always verify against your machine manufacturer’s table before production.

Need the numbers for your exact machine?

See what is inside

SBM Laser Help carries cutting and piercing parameter tables by material, thickness and gas, photo diagnosis of cut defects, machine and chiller error codes, and gas consumption calculators. Free account, no card.