Fiber laser settings for 2 mm stainless steel at 3 kW
Updated:
Short answer
A 3 kW fiber laser cuts 2 mm stainless steel with nitrogen at 12–16 bar and 7.5–26 m/min. For this combination we have three regimes: the base one from the source maker’s table and two alternatives from other sources.
Stainless steel cutting speed and gas pressure at 3 kW
Base regime · Stainless steel · 2 mm · 3 kW
RFL-3000(50u), Cutting head focal length: Collimating 100/Focal 150
Gas
N₂
Gas pressure
12bar
Speed
18–24m/min
Power
100%
Frequency
2500–5000Hz
Duty cycle
100%
Focus
in the app
Cutting height
in the app
Nozzle
in the app
Alternative 1 · Stainless steel · 2 mm · 3 kW
Raycus 3000W, Head: none
Gas
N₂ / air
Gas pressure
16bar
Speed
7.5m/min
Power
100%
Frequency
5000Hz
Duty cycle
100%
Focus
in the app
Cutting height
in the app
Nozzle
in the app
Alternative 2 · Stainless steel · 2 mm · 3 kW
MAX MFSC-3000X-50um, Head: none
Gas
N₂ / air
Gas pressure
16bar
Speed
26m/min
Power
100%
Frequency
5000Hz
Duty cycle
100%
Focus
in the app
Cutting height
in the app
Nozzle
in the app
Which regime to start with
- Base regime. The starting point for most 3 kW machines, from the source maker’s own table.
- Alternative 1. Slower: 7.5 m/min against 18–24 m/min. Gas pressure 4 bar higher. Source: Raycus 3000W, Head: none. Try it when the base regime does not cut through or leaves burr on the bottom edge.
- Alternative 2. Faster: 26 m/min against 18–24 m/min. Gas pressure 4 bar higher. Source: MAX MFSC-3000X-50um, Head: none. Try it when the cut is clean and you want more speed; if the edge gets worse, go back to the base regime.
Cutting time and gas consumption per metre
At these speeds one metre of cut takes about 2–8 seconds. Nitrogen flow through the nozzle is about 29.5–38.6 m³ per hour, or 20–86 litres per metre of cut, not counting piercing.
Stainless steel cutting speed chart: neighbouring thickness and power
| Thickness · power | Gas | Speed, m/min |
|---|---|---|
| 1 mm · 3 kW | N₂ | 28–35 |
| 2 mm · 2 kW | N₂ / air | 10 |
| 2 mm · 3 kW | N₂ | 18–24 |
| 2 mm · 4 kW | N₂ | 15–20 |
| 2 mm · 6 kW | N₂ | 25–30 |
| 3 mm · 3 kW | N₂ | 7–10 |
| 4 mm · 3 kW | N₂ | 5–6.5 |
Common stainless steel cutting defects with nitrogen




Not sure which one you have? Send a photo of the edge to the app and it names the defect and the fix.
Related questions
- What is the thickest stainless steel a 3 kW fiber laser cuts?
- Our tables go up to 16 mm stainless steel at 3 kW, at 0.3 m/min with nitrogen or air. The next thickness, 18 mm, starts from 6 kW.
- Why is the speed a range?
- Sheet surface, stainless steel grade, gas purity and pressure at the nozzle and the state of the protective window all shift the result. Start at the lower value, make a test cut and raise the speed in 5% steps while the bottom edge stays clean.
- Where are focus, cutting height and nozzle?
- They depend on the cutting head and lens, so a single number is often wrong for your machine. The app shows the full regime and fits it to the machine you add to your profile.