Fiber laser settings for 2 mm mild steel at 2 kW

Updated:

Short answer

A 2 kW fiber laser cuts 2 mm mild steel with oxygen at 1.5–1.6 bar and 5.2–5.5 m/min or with nitrogen or air at 16 bar and 9 m/min. For this combination we have four regimes: the base one from the source maker’s table and three alternatives from other sources.

Mild steel cutting speed and gas pressure at 2 kW

Base regime · Mild steel · 2 mm · 2 kW
2000W(50u), Cutting head focal length: Collimating 100/Focal 125
Gas
O₂
Gas pressure
1.6bar
Speed
5.2m/min
Power
100%
Frequency
5000Hz
Duty cycle
100%
Focus
in the app
Cutting height
in the app
Nozzle
in the app
Alternative 1 · Mild steel · 2 mm · 2 kW
Raycus 2000W, Head: none
Gas
N₂ / air
Gas pressure
16bar
Speed
9m/min
Power
100%
Frequency
5000Hz
Duty cycle
100%
Focus
in the app
Cutting height
in the app
Nozzle
in the app
Alternative 2 · Mild steel · 2 mm · 2 kW
Raycus 2000W, Head: none
Gas
O₂
Gas pressure
1.6bar
Speed
5.2m/min
Power
100%
Frequency
5000Hz
Duty cycle
100%
Focus
in the app
Cutting height
in the app
Nozzle
in the app
Alternative 3 · Mild steel · 2 mm · 2 kW
Max Single module MFSC-2000X, Head: none
Gas
O₂
Gas pressure
1.5bar
Speed
5.5m/min
Power
100%
Frequency
5000Hz
Duty cycle
100%
Focus
in the app
Cutting height
in the app
Nozzle
in the app

Which regime to start with

Cutting time and gas consumption per metre

At these speeds one metre of cut takes about 7–12 seconds. Oxygen flow through the nozzle is about 1.3–1.4 m³ per hour, or 4 litres per metre of cut, not counting piercing. Nitrogen or air flow through the nozzle is about 38.6 m³ per hour, or 71 litres per metre of cut, not counting piercing.

Mild steel cutting speed chart: neighbouring thickness and power

Thickness · powerGasSpeed, m/min
1 mm · 2 kW N₂ / air25
2 mm · 1.5 kW O₂5
2 mm · 2 kW O₂5.2
2 mm · 3 kW N₂ / air16–20
2 mm · 3 kW O₂3.8–4.2
2 mm · 4 kW N₂ / air12–15
3 mm · 2 kW O₂4.2
4 mm · 2 kW O₂3

Nitrogen or air cuts about 1.3 times as fast as oxygen here, but needs 1 kW.

Common mild steel cutting defects with oxygen and with nitrogen or air

Cut loss / Beam reflection
Cut loss / Beam reflection The beam breaks down, upward sparking occurs, and the metal is not cut through along the contour. Cause: Insufficient energy density, excessive cutting speed, incorrect focus. First step: Decrease the speed (step 5%). Fiber laser stopped cutting through the sheet — what is wrong?
Burn-throughs in the lower section (Breakthrough)
Burn-throughs in the lower section (Breakthrough) Burnout of metal at the bottom of the edge with formation of craters and buildup. Cause: Excessive cutting speed combined with insufficient assist gas pressure. First step: Decrease the cutting speed (step 5%). Where should the focus sit for stainless steel and mild steel?
Sharp hard dross
Sharp hard dross A sharp welded dross forms along the entire bottom edge. Cause: Focus set too deep, assist gas flow rate too low. First step: Lower/raise the focus (step 0.5 mm). How do I get rid of dross when cutting mild steel with oxygen?
Hard metallic dross
Hard metallic dross A dense, hard-to-remove welded dross forms on the bottom edge of the part, requiring grinding with an angle grinder. Cause: Low oxygen pressure, excessive cutting speed, focus position set too high, insufficient power. First step: Increase the oxygen pressure (step 0.1 bar). How do I get rid of dross when cutting mild steel with oxygen?

Not sure which one you have? Send a photo of the edge to the app and it names the defect and the fix.

Related questions

What is the thickest mild steel a 2 kW fiber laser cuts?
Our tables go up to 20 mm mild steel at 2 kW, at 0.4 m/min with oxygen. The next thickness, 22 mm, starts from 3 kW.
Why is the speed a range?
Sheet surface, mild steel grade, oxygen purity and the state of the protective window all shift the result. Start at the lower value, make a test cut and raise the speed in 5% steps while the bottom edge stays clean.
Where are focus, cutting height and nozzle?
They depend on the cutting head and lens, so a single number is often wrong for your machine. The app shows the full regime and fits it to the machine you add to your profile.

Ranges are given for a typical 3–6 kW fiber machine with a clean beam path. Always verify against your machine manufacturer’s table before production.

Need the numbers for your exact machine?

See what is inside

SBM Laser Help carries cutting and piercing parameter tables by material, thickness and gas, photo diagnosis of cut defects, machine and chiller error codes, and gas consumption calculators. Free account, no card.