Fiber laser settings for 1 mm stainless steel at 1 kW
Updated:
Short answer
A 1 kW fiber laser cuts 1 mm stainless steel with nitrogen or air at 14–16 bar and 8–23 m/min. For this combination we have three regimes: the base one from the source maker’s table and two alternatives from other sources.
Stainless steel cutting speed and gas pressure at 1 kW
Base regime · Stainless steel · 1 mm · 1 kW
1000W(50u), Cutting head focal length: Collimating 100/Focal 125
Gas
N₂ / air
Gas pressure
14bar
Speed
21–23m/min
Power
100%
Frequency
5000Hz
Duty cycle
100%
Focus
in the app
Cutting height
in the app
Nozzle
in the app
Alternative 1 · Stainless steel · 1 mm · 1 kW
Cutting with protective film. Source model: IPG 1000W, Head: Raytools 240
Gas
N₂ / air
Gas pressure
16bar
Speed
8m/min
Power
100%
Frequency
5000Hz
Duty cycle
100%
Focus
in the app
Cutting height
in the app
Nozzle
in the app
Alternative 2 · Stainless steel · 1 mm · 1 kW
Max MFSC-1000X QBH, Head: none
Gas
N₂ / air
Gas pressure
16bar
Speed
15.5m/min
Power
100%
Frequency
5000Hz
Duty cycle
100%
Focus
in the app
Cutting height
in the app
Nozzle
in the app
Which regime to start with
- Base regime. The starting point for most 1 kW machines, from the source maker’s own table.
- Alternative 1. Slower: 8 m/min against 21–23 m/min. Gas pressure 2 bar higher. Source: Cutting with protective film. Source model: IPG 1000W, Head: Raytools 240. Try it when the base regime does not cut through or leaves burr on the bottom edge.
- Alternative 2. Slower: 15.5 m/min against 21–23 m/min. Gas pressure 2 bar higher. Source: Max MFSC-1000X QBH, Head: none. Try it when the base regime does not cut through or leaves burr on the bottom edge.
Cutting time and gas consumption per metre
At these speeds one metre of cut takes about 3–8 seconds. Nitrogen or air flow through the nozzle is about 19.1–38.6 m³ per hour, or 14–80 litres per metre of cut, not counting piercing.
Stainless steel cutting speed chart: neighbouring thickness and power
| Thickness · power | Gas | Speed, m/min |
|---|---|---|
| 0.8 mm · 1 kW | N₂ / air | 20 |
| 1 mm · 500 W | N₂ / air | 11–13 |
| 1 mm · 1 kW | N₂ / air | 21–23 |
| 1 mm · 1.5 kW | N₂ / air | 20 |
| 1 mm · 2 kW | N₂ / air | 28 |
| 2 mm · 1 kW | N₂ / air | 6.5–7 |
| 3 mm · 1 kW | N₂ / air | 2.3–2.5 |
Common stainless steel cutting defects with nitrogen or air




Not sure which one you have? Send a photo of the edge to the app and it names the defect and the fix.
Related questions
- What is the thickest stainless steel a 1 kW fiber laser cuts?
- Our tables go up to 6 mm stainless steel at 1 kW, at 0.5–0.6 m/min with nitrogen or air. The next thickness, 8 mm, starts from 2 kW.
- Why is the speed a range?
- Sheet surface, stainless steel grade, gas purity and pressure at the nozzle and the state of the protective window all shift the result. Start at the lower value, make a test cut and raise the speed in 5% steps while the bottom edge stays clean.
- Where are focus, cutting height and nozzle?
- They depend on the cutting head and lens, so a single number is often wrong for your machine. The app shows the full regime and fits it to the machine you add to your profile.