Fiber laser settings for 3 mm mild steel at 3 kW

Updated:

Short answer

A 3 kW fiber laser cuts 3 mm mild steel with oxygen at 0.5–0.8 bar and 2.04–4 m/min or with air at 3.9–20 bar and 7.7–12 m/min. For this combination we have 11 regimes: the base one from the source maker’s table and 10 alternatives from other sources.

Mild steel cutting speed and gas pressure at 3 kW

Base regime · Mild steel · 3 mm · 3 kW
RFL-3000(50u), Cutting head focal length: Collimating 100/Focal 150
Gas
O₂
Gas pressure
0.6bar
Speed
3.2–3.6m/min
Power
70%
Frequency
5000Hz
Duty cycle
70%
Focus
in the app
Cutting height
in the app
Nozzle
in the app
Alternative 1 · Mild steel · 3 mm · 3 kW
MAX, Head: none
Gas
Air
Gas pressure
12bar
Speed
10m/min
Power
100%
Frequency
2000Hz
Duty cycle
95%
Focus
in the app
Cutting height
in the app
Nozzle
in the app
Alternative 2 · Mild steel · 3 mm · 3 kW
MAX, Head: Precitec
Gas
Air
Gas pressure
20bar
Speed
7.7m/min
Power
100%
Frequency
1400Hz
Duty cycle
95%
Focus
in the app
Cutting height
in the app
Nozzle
in the app
Alternative 3 · Mild steel · 3 mm · 3 kW
GW, Head: ECA740SS
Gas
Air
Gas pressure
3.9bar
Speed
8m/min
Power
100%
Frequency
5000Hz
Duty cycle
100%
Focus
in the app
Cutting height
in the app
Nozzle
in the app
Alternative 4 · Mild steel · 3 mm · 3 kW
MAX, Head: Raytools bm111
Gas
Air
Gas pressure
12bar
Speed
12m/min
Power
100%
Frequency
5000Hz
Duty cycle
100%
Focus
in the app
Cutting height
in the app
Nozzle
in the app
Alternative 5 · Mild steel · 3 mm · 3 kW
MAX 3000W, Head: OSPRI
Gas
N₂ / air
Gas pressure
16bar
Speed
8m/min
Power
100%
Frequency
2000Hz
Duty cycle
80%
Focus
in the app
Cutting height
in the app
Nozzle
in the app
Alternative 6 · Mild steel · 3 mm · 3 kW
MAX MFSC-3000X-50um, Head: none
Gas
O₂
Gas pressure
0.8bar
Speed
3.6m/min
Power
100%
Frequency
5000Hz
Duty cycle
100%
Focus
in the app
Cutting height
in the app
Nozzle
in the app
Alternative 7 · Mild steel · 3 mm · 3 kW
MAX, Head: none
Gas
O₂
Gas pressure
0.5bar
Speed
4m/min
Power
80%
Frequency
5000Hz
Duty cycle
100%
Focus
in the app
Cutting height
in the app
Nozzle
in the app
Alternative 8 · Mild steel · 3 mm · 3 kW
Raycus, Head: Raytools bm111
Gas
O₂
Gas pressure
0.6bar
Speed
3.6m/min
Power
70%
Frequency
5000Hz
Duty cycle
100%
Focus
in the app
Cutting height
in the app
Nozzle
in the app
Alternative 9 · Mild steel · 3 mm · 3 kW
Raycus, Head: none
Gas
O₂
Gas pressure
0.57bar
Speed
2.04m/min
Power
100%
Frequency
5000Hz
Duty cycle
85%
Focus
in the app
Cutting height
in the app
Nozzle
in the app
Alternative 10 · Mild steel · 3 mm · 3 kW
Raycus, Head: Raytools
Gas
O₂
Gas pressure
0.7bar
Speed
3.9m/min
Power
93%
Frequency
5000Hz
Duty cycle
100%
Focus
in the app
Cutting height
in the app
Nozzle
in the app

Which regime to start with

Cutting time and gas consumption per metre

At these speeds one metre of cut takes about 5–29 seconds. Oxygen flow through the nozzle is about 0.9–3.4 m³ per hour, or 4–27 litres per metre of cut, not counting piercing. Air flow through the nozzle is about 6.3–190.5 m³ per hour, or 13–412 litres per metre of cut, not counting piercing.

Mild steel cutting speed chart: neighbouring thickness and power

Thickness · powerGasSpeed, m/min
1 mm · 3 kW N₂ / air28–35
2 mm · 3 kW N₂ / air16–20
2 mm · 3 kW O₂3.8–4.2
3 mm · 2 kW O₂4.2
3 mm · 3 kW O₂3.2–3.6
3 mm · 4 kW N₂ / air8–12
3 mm · 4 kW O₂4–4.5
3 mm · 6 kW N₂ / air12–14
3 mm · 6 kW O₂3.5–4.2
4 mm · 3 kW O₂3–3.2
5 mm · 3 kW O₂2.7–3

Going from 3 kW to 4 kW gives about 25% more speed on 3 mm with oxygen. Nitrogen or air cuts about 2.9 times as fast as oxygen here, but needs 4 kW.

Common mild steel cutting defects with oxygen and with air

Roughness with fine burrs
Roughness with fine burrs Rough cut surface across the full material thickness with formation of fine powdery dross on the bottom. Cause: Focus position set too high, oxygen pressure too low. First step: Raise/lower the focus (step 0.5 mm). Why is the cut edge rough and striated instead of smooth?
Cut loss / Beam reflection
Cut loss / Beam reflection The beam breaks down, upward sparking occurs, and the metal is not cut through along the contour. Cause: Insufficient energy density, excessive cutting speed, incorrect focus. First step: Decrease the speed (step 5%). Fiber laser stopped cutting through the sheet — what is wrong?
Burn-throughs in the lower section (Breakthrough)
Burn-throughs in the lower section (Breakthrough) Burnout of metal at the bottom of the edge with formation of craters and buildup. Cause: Excessive cutting speed combined with insufficient assist gas pressure. First step: Decrease the cutting speed (step 5%). Where should the focus sit for stainless steel and mild steel?
Sharp hard dross
Sharp hard dross A sharp welded dross forms along the entire bottom edge. Cause: Focus set too deep, assist gas flow rate too low. First step: Lower/raise the focus (step 0.5 mm). How do I get rid of dross when cutting mild steel with oxygen?

Not sure which one you have? Send a photo of the edge to the app and it names the defect and the fix.

Related questions

What is the thickest mild steel a 3 kW fiber laser cuts?
Our tables go up to 26 mm mild steel at 3 kW, at 0.23 m/min with oxygen. The next thickness, 30 mm, starts from 8 kW.
Why is the speed a range?
Sheet surface, mild steel grade, oxygen purity and the state of the protective window all shift the result. Start at the lower value, make a test cut and raise the speed in 5% steps while the bottom edge stays clean.
Where are focus, cutting height and nozzle?
They depend on the cutting head and lens, so a single number is often wrong for your machine. The app shows the full regime and fits it to the machine you add to your profile.

Ranges are given for a typical 3–6 kW fiber machine with a clean beam path. Always verify against your machine manufacturer’s table before production.

Need the numbers for your exact machine?

See what is inside

SBM Laser Help carries cutting and piercing parameter tables by material, thickness and gas, photo diagnosis of cut defects, machine and chiller error codes, and gas consumption calculators. Free account, no card.